AWS/ASME SFA - 5.20

E71T-1C

EN ISO 17632 - A

T46 2 P C 1

TS EN ISO 17632 - A

T46 2 P C 1

Rutile type flux cored wire with fast-freezing slag. Especially designed for welding with CO2 (carbondioxide) gas, in shipbuilding and steel construction. Owing to its easily controllable weld pool, electrode is well suited for positional welding with higher currents, resulting in increased deposition rates. Particularly suited for welding in the horizontal-vertical position, e.g. in tank welding. Electrode of 1.2 mm in diameter is also suitable for vertical-down welding. Low spatter loss, easy slag removal, finely ripped pore-free welds blending into base metal without undercut.

AWS/ASME SFA - 5.20

E71T-1C H4

EN ISO 17632 - A

T46 2 P C 1 H5

TS EN ISO 17632 - A

T46 2 P C 1 H5

Rutile type flux cored wire with fast-freezing slag. Especially designed for welding with CO2 (carbondioxide) gas, in shipbuilding and steel construction. Owing to its easily controllable weld pool, electrode is well suited for positional welding with higher currents, resulting in increased deposition rates. Its special vacuum packing provides low diffusible hydrojen level in weld metal, in the case of proper handling and storage conditions. Electrode of 1.20 mm in diameter is also suitable for vertical-down welding. Low spatter loss, easy slag removal in the fillet and norrow grooves, finely ripped pore-free welds blending into base metal without undercut.

AWS/ASME SFA - 5.20

E71T-1M

EN ISO 17632 - A

T46 2 P M 1

TS EN ISO 17632 - A

T46 2 P M 1

Rutile type flux cored wire, especially designed for welding in steel construction, piping, machine fabrication and shipbuilding by using mix shielding gas. Owing to its easily controllable weld pool and fast freezing slag particularly suited for welding in all position. Good gap-bridging property, low spatter loss, easy slag removal even in narrow grooves. Finely ripped pore-free welds blending into base metal without undercut.

AWS/ASME SFA - 5.18

E70C-GM H4

EN ISO 17632 - A

T46 3 M M 2 H5

TS EN ISO 17632 - A

T46 3 M M 2 H5

Slagless metal powder cored electrode with outstanding welding properties in the short-arc and spray arc range. Almost spatter-free when welding in the spray-arc range with mixed gas. Good restriking, even with cold wire tip, thus being suitable for robot application. Characteristic features; high deposition rate and welding speed, good side wall fusion, finely rippled welds, without undercutting into the base metal, not even on contaminated or corroded metal surfaces. Little formation of silicates on weld surface, so that multi-pass welds can be made without cleaning. Due to its easily controlable weld pool in the short-arc range, FCW 20 is well-suited for root-and positional welding and gap bridging. 

AWS/ASME SFA - 5.18

E70C-6M H4

EN ISO 17632 - A

T46 4 M M 2 H5

TS EN ISO 17632 - A

T46 4 M M 2 H5

Slagless metal powder cored electrode with outstanding welding properties in the short-arc and spray arc range. Almost spatter-free when welding in the spray-arc range with mixed gas. Good restriking, even with cold wire tip, thus being suitable for robot application. Characteristic features; high deposition rate and welding speed, good side wall fusion, finely rippled welds, without undercutting into the base metal, not even on contaminated or corroded metal surfaces. Little formation of silicates on weld surface, so that multi-pass welds can be made without cleaning. Due to its easily controlable weld pool in the short-arc range, FCW 21 is well-suited for root-and positional welding and gap bridging.

AWS/ASME SFA - 5.20

E70T-5M H4

AWS/ASME SFA - 5.20

E70T-5C H4

EN ISO 17632 - A

T42 4 B C 3 H5

EN ISO 17632 - A

T42 4 B M 3 H5

TS EN ISO 17632 - A

T42 4 B C 3 H5

TS EN ISO 17632 - A

T42 4 B M 3 H5

Basic type flux cored wire for welding thick steel sections and dynamically loaded structures, where high toughness is required. Provides high mechanical properties and high crack resistant weld metal. Suitable to welding of boiler, tank, pressure vessel, heavy machine production and heavy constructions. Weld are metallurgically clean and are of X-ray quality. FCW 30 is also suitable for welding high carbon steels and buffer application on worn parts before hardfacing.

AWS/ASME SFA - 5.29

E81T1-Ni1C

EN ISO 17632 - A

T46 4 1Ni P C 1 H5

TS EN ISO 17632 - A

T46 4 1Ni P C 1 H5

Rutile type flux cored wire, designed for welding fine grained structural steels. Succesfully used in single and multirun welding of especially in steel construction, bridge, offshore platform, shipbuilding and pipe laying. Owing to its easily controllable weld pool and fast freezing slag, suited for welding in all position easily. It's metal recovery provides ability of good gap bridging and filling property.  Because of nickel alloy, weld metal yield and tensile strength is high and  weld metal is proper to use on fine grained steels at operating temperatures +450°C down to -40°C. Diffusible hydrogen content is <5ml per 100g deposited weld metal, so highly resistant to  cold cracking. Has a stable and quite arc with low spatter loss. Has easily removable slag, generally self removed. 

AWS/ASME SFA - 5.36

E81T-1 M21A6 Ni1

AWS/ASME SFA - 5.29

E81T1-Ni1M

EN ISO 17632 - A

T46 4 1Ni P M 1 H5

TS EN ISO 17632 - A

T46 4 1Ni P M 1 H5

Rutile type flux cored wire, designed for welding fine grained structural steels by using mix shielding gas. Succesfully used in single and multirun welding of especially in steel construction, bridge, offshore platform, shipbuilding and pipe laying. Owing to its easily controllable weld pool and fast freezing slag, suited for welding in all position easily. It?s metal recovery provides ability of good gap bridging and filling property.  Because of nickel alloy, weld metal yield and tensile strength is high and  weld metal is proper to use on fine grained steels at operating temperatures +450°C down to -40°C. Diffusible hydrogen content is <5ml per 100g deposited weld metal, so highly resistant to  cold cracking. Has a stable and quite arc with low spatter loss. Has easily removable slag, generally self removed. 

AWS/ASME SFA - 5.29

E81T1-W2C

EN ISO 17632 - B

T553T1-1C A-NCC1

TS EN ISO 17632 - B

T553T1-1C A-NCC1

Rutile type flux cored wire with fast freezing slag. Especially designed for welding fine grained structural steels. Suitable for welding in steel construction in single and multi-run welding in all position. Owing to its easily controllable weld pool and fast freezing slag particularly suited for welding in all position. Has a stable and quite arc with low spatter loss.

AWS/ASME SFA - 5.29

E81T1-A1C

EN ISO 17634 - A

T MoL P C 1 H5

TS EN ISO 17634 - A

T MoL P C 1 H5

Flux cored wire designed for welding boiler, pipe steels, steam generators and other equipments, subjected to operating temperatures up to 500°C. Suitable to use in all position welding and preferred to use where high mechanical properties and X-ray quality are required.